Toyota Tundra Wheel and Tire Fitment Guide: 2000 to Present, TRD Pro, Capstone and 1794

Toyota Tundra TRD Pro on black aftermarket wheels and all-terrain tires

The Toyota Tundra changed bolt patterns twice. 2000–2006 trucks use 6×139.7 (6×5.5) with M12 x 1.5 studs, 2007–2021 trucks use 5×150 with M14 x 1.5 studs, and 2022-and-newer trucks are back on 6×139.7 with M14 x 1.5 studs and a 95.1 mm hub. Toyota’s alloy-wheel torque is 97 lb-ft from 2007 on.

The Tundra is the one Toyota truck where “what year is it?” decides everything. A 2004 and a 2024 share a bolt pattern and almost nothing else. A 2015 shares nothing with either of them. Every week we talk to someone who bought a set of take-offs that looked right in the photos and found five holes where the truck has six studs, or a 95.1 mm bore that will not slide over an older hub. This guide sorts out which Tundra you have, then covers lug hardware and torque, factory wheel and tire sizes by trim, offsets, what fits stock, leveled, and lifted trucks, and what is different on the TRD Pro and Capstone. We built it from Toyota owner’s manuals, a Toyota brochure, and a Toyota press release, cross-checked against fitment databases. Where a number comes from a database rather than Toyota, or the sources disagree, we say so.

How we approach a Tundra order: generation first, then tire size, then the wheel. Our Toyota Tundra wheels and tires page only shows wheels and tires that fit the year and trim you enter, and those results are covered by our 100% Fitment Guarantee. Read this first so you know what to enter, especially if the truck has already been leveled or lifted.

What bolt pattern, center bore, and lug thread does each Tundra generation use?

Two bolt patterns, three hub sizes, and two stud threads across three generations. Toyota’s owner’s manuals print the torque but not the bolt circle, hub diameter, or stud thread, so those columns come from fitment databases that agree with each other. Toyota’s own parts catalog does list “6 on 139.7 mm” for its 2022-and-newer accessory wheels, which confirms the current pattern. The torque column is from the Toyota owner’s manuals we pulled for each generation.

Toyota Tundra wheel hardware by generation
Generation Model years Bolt pattern Stud thread Center bore Factory lug torque (owner’s manual)
1st gen (XK30/XK40) 2000–2006 6×139.7 (6×5.5) (databases) M12 x 1.5 (databases) 106.1 mm (databases) 110 N·m (83 lb-ft) in the 2001 and 2005 manuals
2nd gen (XK50) 2007–2021 5×150 (databases) M14 x 1.5 (databases) About 110 mm; most databases list 110.1 mm, some 110.0 or 110.5 97 lb-ft (131 N·m) aluminum; 154 lb-ft (209 N·m) steel in the 2007, 2014 and 2018 manuals
3rd gen (XK70), incl. TRD Pro and Capstone 2022–present 6×139.7 (6×5.5) (databases; Toyota parts catalog) M14 x 1.5 (databases) 95.1 mm (databases) 97 lb-ft (131 N·m) aluminum; 154 lb-ft (209 N·m) steel in the 2022 and 2025 manuals

The 2007 change is the one people miss on torque. The 2007 Tundra owner’s manual lists two numbers and two nut types: a flat-washer nut on aluminum wheels at 97 lb-ft (131 N·m) and a taper nut on steel wheels at 154 lb-ft (209 N·m). It adds that if you put the steel spare into service, it gets the 154 figure. That is a 57 lb-ft gap on the same truck. A base Tundra on steel wheels torqued to the alloy number is under-torqued, and an alloy wheel torqued to the steel number is over-torqued. Every later book we checked, through the 2025 manuals, repeats the same pair.

First gen trucks are simpler: one figure, 110 N·m. The 2001 Tundra owner’s manual prints it as 83.2 lb-ft and the 2005 book as 83 lb-ft. Toyota’s manuals on every generation tell owners never to oil or grease the studs or nuts, and the 2007-and-newer books add a re-tighten within 100 miles after a wheel change. We go further on aftermarket wheels and re-check after the first 25 to 50 miles. New wheels seat in, and a nut that was right in the driveway is not always right a week later.

The 2007–2021 truck is the largest pool of Tundras we see, and it shares no bolt pattern with the trucks before or after it. Our 5×150 wheels page is where those builds start.

For 2000–2006 and 2022-and-newer trucks, start with our 6×5.5 wheels and filter by offset, hub, and thread for your year.

What wheel and tire sizes came on each Tundra?

Wheel and tire sizes below come from Toyota’s owner’s manuals, with the trim assignments for 2022 and newer from Toyota’s 2022 brochure. Toyota does not print offsets in those books, so the offsets come from fitment databases that agree with each other. Where they do not agree, or only one source lists a figure, we say so in the table. Diameters are calculated from the tire size and rounded.

Factory Tundra wheel and tire sizes (Toyota manuals and brochure; offsets from cross-checked databases)
Generation or trim Factory wheel and offset Factory tire Approx. tire diameter
1st gen (2000–2006) 16 x 7 at about +15 mm; 17 x 7.5 at about +15 mm on later trucks P245/70R16; P265/70R16; P265/65R17 (listed in the 2005 and 2006 manuals) 29.5 in.; 30.6 in.; 30.6 in.
2nd gen, 18-inch (2007–2021) 18 x 8 at about +60 mm (steel on base trucks, alloy on most others) P255/70R18; P275/65R18 32.1 in.
2nd gen, 20-inch (2007–2021) 20 x 8 at about +60 mm P275/55R20 31.9 in.
2nd gen TRD Pro (2015–2021) 18-inch; databases list 18 x 8 (confirm offset) P275/65R18 class; check your placard 32.1 in.
3rd gen SR (2022–present) 18 x 7.5 styled steel at about +60 mm 245/75R18 32.5 in.
3rd gen SR5 and 18-inch TRD Off-Road 18 x 7.5 alloy at about +60 mm 265/70R18 (Michelin LTX Trail all-terrain with the TRD Off-Road Package) 32.6 in.
3rd gen Limited, Platinum, 1794 Edition, 20-inch TRD Off-Road and TRD Sport 20 x 8 at about +60 mm or 20 x 8.5 at about +55 mm, depending on the wheel 265/60R20 (Falken Wildpeak all-terrain with the 20-inch TRD Off-Road Package) 32.5 in.
3rd gen TRD Pro (2022–present) 18 x 8.5 forged BBS at about +47.5 mm 285/65R18 Falken Wildpeak all-terrain 32.6 in.
3rd gen Capstone (2022–present) 22 x 8 at about +60 mm 265/50R22 32.4 in.

Two things stand out. First, since 2007 every factory Tundra tire has landed between about 31.9 and 32.6 inches, whatever the wheel diameter. Toyota changes the sidewall, not the overall height. So a “bigger” 20 or 22 is a styling choice, and a true 34 or 35 is a real change in clearance. Second, the offsets are high. Most 2007-and-newer factory wheels sit at about +60 mm, which is why the Tundra looks narrow-tracked to some owners and why a modest aftermarket offset moves the wheel a long way outward.

The trim assignments for 2022 and newer come from the 2022 Tundra brochure: 18-inch styled steel on the SR, 18-inch alloys on the SR5, 20-inch wheels on the Limited, Platinum, and 1794 Edition, 18-inch forged BBS wheels on the TRD Pro with a 1.1-inch front lift, and 22-inch wheels on the Capstone. The TRD Off-Road Package came on 18-inch wheels with 265/70R18 Michelin LTX Trail tires or 20-inch black wheels with 265/60R20 Falken Wildpeak tires, depending on the grade. Packages move around from year to year, so read your placard rather than the window sticker of a different truck.

The manuals add details worth knowing. The SR’s 18 x 7.5 steel-wheel setup lists only the 154 lb-ft steel figure, and the 2022-and-newer manuals list an 18 x 7 spare wheel on every setup, sometimes with a 245/75R18 spare tire even on trucks that run 265/70R18 or 265/60R20 on the ground. The 2022 Tundra hybrid owner’s manual lists the TRD Pro’s 285/65R18 on an 18 x 8.5 and the Capstone’s 265/50R22 on a 22 x 8. If you plan to upsize, plan where a matching full-size spare will live.

One more for owners shopping new. Toyota’s 2027 Tundra press release, dated November 5, 2026, adds a Trailhunter package for 2027, built on the SR5 grade with Old Man Emu suspension, bronze-colored wheels, and 265/70R18 Michelin LTX Trail tires, and gives the TRD Pro new FOX QS3 shocks. Toyota had not published wheel width or offset for the Trailhunter when we checked, so confirm those against the truck before you order.

How do offset and backspacing change what fits on a Tundra?

Offset is the distance in millimeters from the wheel’s centerline to its mounting face. Positive offset tucks the wheel in toward the frame; negative pushes it out. Backspacing is the distance in inches from the mounting face to the inner lip, and on a Tundra it decides whether a wide tire touches the upper control arm or the frame at full lock. The two are linked by width, so neither number means much alone. Our wheel offset and backspacing calculator does the conversion for any width and offset.

The table compares common sizes against two factory baselines: a 2007–2021 18 x 8 at +60 mm and a 2022-and-newer 18 x 7.5 at +60 mm. The figures are geometry, calculated from width and offset, so they apply to any brand.

Backspacing and outer lip position against 2007–2021 and 2022-and-newer factory wheels
Wheel Backspacing Outer lip vs. 2007–2021 18 x 8, +60 mm Outer lip vs. 2022+ 18 x 7.5, +60 mm
18 x 8, +60 mm (2nd gen factory) 6.86 in. Baseline 0.25 in. farther out
18 x 7.5, +60 mm (3rd gen factory) 6.61 in. 0.25 in. farther in Baseline
18 x 8.5, +47.5 mm (3rd gen TRD Pro) 6.62 in. 0.74 in. farther out 0.99 in. farther out
18 x 9, +18 mm 5.71 in. 2.15 in. farther out 2.40 in. farther out
20 x 9, +1 mm 5.04 in. 2.82 in. farther out 3.07 in. farther out
17 x 9, -12 mm 4.53 in. 3.33 in. farther out 3.58 in. farther out
20 x 10, -18 mm 4.79 in. 4.07 in. farther out 4.32 in. farther out

Read the middle rows twice. An 18 x 9 at +18 mm, one of the most common Tundra wheels we sell, sits more than 2 inches farther out than the factory wheel on either generation. That is the look most owners want, and it is also why we ask about tire width before we recommend it: the tire grows outward with the wheel, and on a truck built around +60 mm wheels, the fender lip gets close fast. A 20 x 10 at -18 mm puts the lip about 4 inches outboard. More poke is more leverage on the wheel bearings and steering parts, and on a truck that tows, we would rather keep it moderate.

What size tires fit a Tundra on stock suspension, a leveling kit, and a lift?

The table shows the starting points our specialists use on 2007-and-newer Tundras. These are typical community fitments, not Toyota specs and not a guarantee. A tire that clears with the truck parked can still touch at full lock, under compression, or with a loaded bed and a trailer on the hitch.

Typical 2007-and-newer Tundra tire, suspension, and wheel combinations (typical community fitment, not guaranteed)
Tire 2007–2021 (2nd gen) 2022 and newer (3rd gen) Typical wheel and offset
About 32 to 32.6 in. (factory sizes) Fits Fits Factory sizes and offsets
About 33 in. (285/70R17 or 275/70R18 on 2nd gen; 285/65R18 on 3rd gen) Usually fits stock; light rub at full lock is possible Usually fits stock; 285/65R18 is the TRD Pro’s factory size 17 x 8.5 to 18 x 9, about 0 to +18 mm
About 34 in. (285/75R17, 285/70R18, 295/70R18 class) Typically a 2 to 2.5 in. front leveling kit, often with the front mud flaps removed Typically a leveling kit, often with mud-flap or front trim work 18 x 9 or 20 x 9, about 0 to +18 mm
35 in. (35×12.50R17, R18 or R20) Typically 3 in. or more of lift plus trimming Typically 3 in. or more of lift plus trimming; less aftermarket history than the 2nd gen 18 x 9 to 20 x 10, about 0 to -18 mm
37 in. Only with a large lift and supporting parts Only with a large lift and supporting parts Set up one truck at a time

Our Tundra lander lists the same pattern of common fitments: 18 x 9 and 20 x 9 with 275/65R18, 275/55R20, and 285/55R20 on stock and mild setups; 18 x 9 with 295/70R18 and 17 x 9 or 20 x 9 with 33×12.50 tires on leveled trucks; and 20 x 10 with 35×12.50R20 on properly lifted trucks. If a 33 is the goal on a 2nd gen, our 285/70R17 tires page has the size most of those trucks run.

Compare tread patterns and load ranges on our 33-inch tires page before you settle on a wheel, since the tire’s load index has to cover a full-size truck.

Where do bigger tires rub on a Tundra?

In our experience the contact points show up in roughly this order:

  • Front mud flaps and the lower bumper or air-dam corners. The first thing a taller tire touches at full lock. Most owners remove the flaps before anything else.
  • Front of the fender liner. Contact at full lock and under compression. Heat-forming or trimming usually handles it.
  • The frame and cab mount area at full lock. Wide tires on high-backspacing wheels can touch here. Less backspacing is the cleaner fix.
  • Upper control arm. A wide tire on a wheel with too much backspacing touches the upper arm, especially after a leveling kit steepens the arm angle. A spacer is not our first choice.

For 35s, the lift is only part of the job. Plan on trimming, an alignment, and a hard look at gearing and braking on a truck that already weighs as much as a Tundra. Our 35-inch tires page is where we would start once the suspension is sorted.

What fits a 2000–2006 Tundra?

The first gen is a smaller truck on smaller tires, about 29.5 to 30.6 inches from the factory. In our experience a tire near 31.6 inches, such as 265/75R16, is a sensible ceiling on a stock first gen, and 33s typically want a lift and trimming. These trucks are now 20 to 26 years old, so we look at ball joints, bushings, and the frame before we size up. Again, typical, not guaranteed.

What changes on 2022-and-newer Tundras?

The driver-assist system cares about ride height. The 2025 Tundra owner’s manual, in the Toyota Safety Sense section, lists a lifted truck among the conditions where the pre-collision and radar cruise systems may not work as designed, except with a Toyota official lift kit up to 4 inches (101 mm) including tire height, and says aftermarket lift kits may degrade system performance. The 2022 manual says the same. Read that section before you plan a lift and 35s on a new truck. And because the smallest factory wheel on these trucks is 18 inches, we do not assume a 17 clears the brakes; we check every wheel.

Will wheels from other Tundras, Toyotas, or trucks fit?

Same bolt pattern does not mean same wheel. The table covers the swaps we get asked about most. Hub and thread figures are from fitment databases.

Common Tundra wheel swaps
Swap Bolts on? What it takes, and our view
2000–2006 wheels onto a 2007–2021 truck (or the reverse) No 6-lug vs. 5-lug. Buy wheels drilled for the truck.
2007–2021 wheels onto a 2022-and-newer truck (or the reverse) No 5×150 vs. 6×139.7. Adapters exist; we do not recommend them on a truck that tows.
2000–2006 wheels onto a 2022-and-newer truck Technically A 106.1 to 95.1 mm ring, M14 x 1.5 nuts that clear the lug holes, and about 45 mm less offset than factory. Older wheels may not carry the load rating. We do not recommend it.
2022-and-newer wheels onto a 2000–2006 truck No The 95.1 mm bore will not fit over the 106.1 mm hub, and the studs are a different thread.
2024+ Tacoma or 2025+ 4Runner wheels onto a 2022-and-newer Tundra Usually Same 6×139.7, 95.1 mm and M14 x 1.5 per databases, but check the wheel’s load rating against a full-size truck and the offset.
2008–2022 Sequoia wheels onto a 2007–2021 Tundra Usually Both 5×150 per databases; bore listings vary (110.1 vs. 110.5 mm), so confirm the hub fit and load rating.

The midsize-truck row deserves a warning. A wheel built for a Tacoma or 4Runner can bolt on and still be rated for less load than a Tundra puts on it, especially loaded or towing. Our Tacoma wheel and tire fitment guide covers the Tacoma side in the same detail.

The 2025-and-newer 4Runner shares the current Tundra’s hub and thread but runs very different offsets; our 4Runner wheel and tire fitment guide covers it.

Other 6×139.7 trucks do not cross over cleanly either. Fitment databases list a 78.1 mm bore on the Silverado 1500 and Sierra 1500 and 77.8 mm on the Ram 1500, both far smaller than any Tundra hub, so those factory wheels will not sit on a Tundra. Most aftermarket 6×139.7 wheels are bored large enough for Toyota hubs and center with a ring. Our Ram 1500 fitment guide explains the Ram side.

What lug nuts and hub-centric rings does a Tundra need with aftermarket wheels?

Three things have to match: thread, seat, and length. Thread is M12 x 1.5 on 2000–2006 trucks and M14 x 1.5 from 2007, according to the fitment databases we checked. Seat is set by the wheel, not the truck. Toyota’s manuals describe a flat-washer nut for the alloy wheels and a taper nut for the steel wheels, and the two are not interchangeable. Most aftermarket wheels use a 60-degree conical seat, so factory Toyota alloy nuts will not clamp an aftermarket wheel the way it was designed to. Our explainer on whether aftermarket wheels need special lug nuts goes through the seat types.

Hub-centric rings bridge the gap between a wheel’s larger center bore and the hub: 106.1 mm on 2000–2006 trucks, about 110 mm on 2007–2021, and 95.1 mm on 2022 and newer. Because the second gen bore is listed at 110.0, 110.1, and 110.5 mm depending on the source, we size rings for those trucks from the wheel maker’s spec and a measurement, not a forum post. Never drill out a wheel’s lug holes or center bore yourself.

Will TPMS work with new wheels on a Tundra?

Federal rules require a TPMS on trucks like these. FMVSS 138 was phased in from the 2006 model year and required all covered light vehicles by September 1, 2007, which generally means the 2008 model year. The rule, published in the Code of Federal Regulations at 49 CFR 571.138, requires a low-pressure warning when a tire falls 25 percent below the recommended cold pressure, and owner’s manual language warning that replacement tires or wheels can stop the system from working. Some late first gen trucks already had it: the 2005 manual describes wheel sensors and a reset switch.

The process changed with the generations. The 2018 Tundra owner’s manual says new sensors must have their ID codes registered in the tire pressure warning computer and tells owners to have a Toyota dealer do it. The 2025 manual says the system must be initialized after rotating or changing tires and after registering IDs, sets the current cold pressure as the benchmark through Vehicle Settings and TPWS, and covers switching between two registered wheel sets. It also says sensors may not work properly with non-genuine wheels. A shop with the right TPMS tool can usually register sensors too.

In practice, healthy factory sensors often move to aftermarket wheels that accept a valve-stem sensor, and we check that before we reuse anything. Our explainer on whether your old TPMS sensors can move to new wheels covers when to reuse sensors and when to replace them. A larger LT tire may want a different cold pressure than the placard. If it does, initialize the system at the new pressure.

Does a bigger tire change gearing and the speedometer?

Yes, on both counts. A taller tire covers more ground per revolution, so the speedometer reads low and the effective axle ratio drops. The math: effective ratio equals the axle ratio times the old tire diameter, divided by the new tire diameter. Take a 3.73 ratio as an example. On a factory 32.6-inch tire, stepping to about 33.7 inches lands near 3.61, and a 35 drops it to about 3.47. A 35 also reads about 7 percent slow on the speedometer. On a Tundra that tows, that is the difference between a truck that holds its gear on a grade and one that hunts. Have the tire size recalibrated after a size change so the speedometer and odometer stay accurate.

What load rating do Tundra wheels and tires need?

Each wheel carries a maximum load rating from its maker, and each tire carries a load index. The placard on the driver’s door jamb gives the factory tire size and pressure, and Toyota’s manuals list the load index of each factory tire: 111 to 114 on the 2007–2021 sizes, and 112 to 116 on 2022-and-newer sizes, with the 265/70R18 and 285/65R18 at 116. Replacement tires should not have a lower load index than the originals, and the wheel should be rated for the truck’s weight with margin for payload and tongue weight. Our Search By Vehicle tool filters Tundra wheels by load rating along with bolt pattern, offset, and center bore, and every order is reviewed by a fitment specialist.

LT tires add stiffer construction and higher load ranges than P-metric and standard-load tires. They ride firmer and weigh more. On a Tundra that tows a heavy camper or hauls a loaded bed every day, we would rather go LT. On a daily driver that rarely carries much, a standard-load or XL tire at the right load index is often the better match.

How do we build a Tundra wheel and tire package?

We recommend a complete set on most Tundra builds, because tire size, wheel width, and offset have to be chosen together. We mount and balance every package on Hunter equipment, and TPMS, lug hardware, hub-centric rings, and Road Force balancing are options at checkout. Before an order ships, a specialist runs a 5-point check of bolt pattern, offset, center bore, width, and brake clearance. On a Tundra, the bolt pattern line is the one that catches people, because three generations use two patterns. Our 100% Fitment Guarantee page explains what is covered. Changing the tire size away from what our Search By Vehicle tool recommends can void it, so tell us about your leveling kit or lift before you order, not after.

Wheels ship out in 2 to 4 business days and mounted packages in 4 to 8, to the lower 48 states. Eligible unused products can be returned within 60 days, subject to the conditions on our returns page. If you would rather spread the cost of a full set, our guide to financing wheels and tires covers the options.

What should you check before you order Tundra wheels and tires?

Run this list in order. It is the same order our specialists use on the phone.

  1. Identify the generation and trim. Note the model year: 2000–2006, 2007–2021, or 2022 and newer. Note the grade (SR, SR5, Limited, Platinum, 1794 Edition, TRD Pro, Capstone), the TRD Off-Road Package, whether it is an i-FORCE MAX hybrid, and any lift or leveling kit.
  2. Read the door placard. Write down the factory tire size, load index, and cold inflation pressure. Replacement tires should not have a lower load index than the originals, and the wheel’s load rating should cover the truck, its payload, and what it tows.
  3. Choose the tire size first. Decide on the tire for how you use the Tundra, then the suspension it typically needs: stock for about 33 inches on a 2007-and-newer truck, a leveling kit for about 34, and a 3-inch or larger lift with trimming for 35s.
  4. Pick wheel diameter, width, and offset for that tire. Start from your truck’s factory offset (about +15 mm on 2000–2006, about +60 mm on most 2007-and-newer wheels, about +47.5 mm on the 2022-and-newer TRD Pro), run the numbers in an offset and backspacing calculator, and check brake clearance.
  5. Confirm bolt pattern, center bore, and lug hardware. Match 6×139.7 / 106.1 mm / M12 x 1.5 on 2000–2006, 5×150 / about 110 mm / M14 x 1.5 on 2007–2021, or 6×139.7 / 95.1 mm / M14 x 1.5 on 2022 and newer. Use a hub-centric ring if the wheel bore is larger than the hub, and buy nuts with the seat the wheel calls for.
  6. Plan TPMS. Order sensors or confirm your old ones are healthy and compatible, have the new sensor IDs registered to the truck after installation, initialize the system at your cold pressure, and check that the TPMS light is off.
  7. Plan driver-assist and speedometer checks. On 2022-and-newer trucks, read the Toyota Safety Sense section of the owner’s manual before changing ride height or tire size. On any year, have the tire size recalibrated if the speedometer reads off.
  8. Install, torque, and re-check. Torque the lug nuts in a star pattern with a torque wrench to your year’s spec (83 lb-ft on 2000–2006; 97 lb-ft alloy or 154 lb-ft steel from 2007), re-check after the first 25 to 50 miles, and get an alignment if lift, tire size, or offset changed.

Frequently asked questions

What is the bolt pattern on a Toyota Tundra?

It depends on the generation. Fitment databases list 6×139.7 (6×5.5) on 2000–2006 trucks, 5×150 on 2007–2021 trucks, and 6×139.7 again on 2022-and-newer trucks. Toyota’s own parts catalog lists 6 on 139.7 mm for its 2022-and-newer accessory wheels. Check the model year before you shop, because wheels from the middle generation do not fit either of the others.

What size lug nuts does a Tundra use?

Fitment databases list M12 x 1.5 studs on 2000–2006 Tundras and M14 x 1.5 on every Tundra from 2007 on. Toyota alloy wheels use a flat-seat nut with a washer and Toyota steel wheels use a tapered nut, while most aftermarket wheels need a 60-degree conical-seat nut, so plan on new lug nuts with most aftermarket wheels.

What is the lug nut torque on a Toyota Tundra?

Toyota’s 2001 and 2005 owner’s manuals list 110 N·m (83 lb-ft) for 2000–2006 trucks. From 2007 on, every manual we checked, through 2025, lists 97 lb-ft (131 N·m) for aluminum wheels and 154 lb-ft (209 N·m) for steel wheels, including the steel spare. Toyota says to retighten the nuts within 100 miles after a wheel change.

What is the center bore on a Tundra?

Fitment databases list 106.1 mm on 2000–2006 trucks, about 110 mm on 2007–2021 trucks (most list 110.1 mm, a few list 110.0 or 110.5), and 95.1 mm on 2022-and-newer trucks. Toyota’s owner’s manuals do not print the hub size. Use a hub-centric ring whenever the wheel’s bore is larger than the hub.

Will 2007–2021 Tundra wheels fit a 2022-and-newer Tundra?

No. The 2007–2021 wheels are drilled 5×150 and the 2022-and-newer truck is 6×139.7, so they cannot bolt on. Adapters that convert one pattern to the other exist, but they push the wheel outward and add another joint to the hub, and we do not recommend them on a full-size truck that tows. Buy wheels drilled for your generation.

What size tires fit a stock or leveled Tundra?

Factory Tundra tires on 2007-and-newer trucks are already about 32 to 32.6 inches. On a stock truck, a 33-inch tire such as 285/70R17 on a 2007–2021 or 285/65R18 on a 2022-and-newer truck typically fits. With a typical 2 to 2.5 inch front leveling kit, about 34 inches typically fits, often with mud-flap or trim work. Treat these as typical, not guaranteed.

What wheels and tires come on the Tundra TRD Pro and Capstone?

On 2022-and-newer trucks, Toyota fits the TRD Pro with 18-inch forged BBS wheels and 285/65R18 Falken Wildpeak all-terrain tires, plus a 1.1-inch front lift; Toyota’s manuals list the wheel as 18 x 8.5. The Capstone uses 22-inch wheels, which the hybrid manual lists as 22 x 8 with 265/50R22 tires.

Can I reuse my Tundra’s TPMS sensors on aftermarket wheels?

Often, if the sensors are healthy and the new wheel’s valve hole accepts them. Toyota’s manuals say new sensors must have their ID codes registered and that sensors may not work properly with non-genuine wheels, so we check compatibility before we reuse anything. The 2025 manual also covers switching between two registered wheel sets.

Who can check your Tundra build before you order?

Send us the year, trim, suspension, and the tire size you want, and a specialist will tell you what fits and what it will take. Call or text 1-866-757-4679 Monday through Friday, 8:30 AM to 6:00 PM Eastern. If the honest answer is that the wheels you found are drilled for a different Tundra generation, we will tell you before you spend the money.

Want to hear from other Tundra owners first? Our customer reviews page shows our 4.8-star Shopper Approved rating across 2,045 reviews.