Toyota 4Runner Wheel and Tire Fitment Guide: 1984 to Present, TRD Pro and Trailhunter

2025+ sixth-generation Toyota 4Runner in gray on bronze 17-inch aftermarket wheels and all-terrain tires outside a tire shop

Every U.S. 4Runner from 1984 on uses a 6×139.7 (6×5.5) bolt pattern. Through 2024 it pairs with a 106.1 mm hub and M12 x 1.5 studs; the 2025-and-newer 4Runner moved to a 95.1 mm hub and M14 x 1.5 studs. Toyota’s torque spec is 76 lb-ft on 2015–2024 alloy wheels and 97 lb-ft on 2025-and-newer alloys.

The 4Runner is easy on the bolt pattern and hard on assumptions. It has been 6×139.7 for forty years, so owners expect any 6-lug Toyota wheel to carry over. Then a 2025 owner orders wheels drilled for the old M12 studs, or a 5th gen owner buys a set of factory 2025 take-offs and finds they will not slide over the older, larger hub. The pattern stayed the same. The hub, the studs, the torque spec, and the factory offset did not. This guide sorts out which 4Runner you have, then covers lug hardware, factory wheel and tire sizes, offsets, what fits on stock, leveled, and lifted trucks, and what is different on the TRD Pro and Trailhunter. We built it from Toyota owner’s manuals and Toyota press material, cross-checked against fitment databases. Where a number comes from a database rather than Toyota, or the sources disagree, we say so.

How we approach a 4Runner order: generation first, then tire size, then the wheel. Our Toyota 4Runner wheels and tires page only shows wheels and tires that fit the year and trim you enter, and those results are covered by our 100% Fitment Guarantee. Read this first so you know what to enter, especially on a 2025-and-newer truck or a 4Runner that has already been lifted.

What bolt pattern, center bore, and lug thread does each 4Runner generation use?

One bolt pattern, two hub sizes, and two stud threads across six generations. Toyota’s owner’s manuals do not print the bolt circle or hub diameter, so the pattern, bore, and thread figures below come from fitment databases that agree with each other. The torque figures are from the Toyota owner’s manuals we pulled for each generation. We could not find a Toyota owner’s manual for the 1984–1995 trucks online, so those rows rest on databases alone and we mark them that way.

Toyota 4Runner wheel hardware by generation
Generation Model years Bolt pattern Stud thread Center bore Factory lug torque (owner’s manual)
1st gen (N60) 1984–1989 6×139.7 (6×5.5) (databases) M12 x 1.5 (databases) 106.1 mm (databases) No Toyota manual found; confirm before you torque
2nd gen (N120/N130) 1990–1995 6×139.7 (6×5.5) (databases) M12 x 1.5 (databases) 106.1 mm (databases) No Toyota manual found; confirm before you torque
3rd gen (N180) 1996–2002 6×139.7 (6×5.5) M12 x 1.5 106.1 mm 110 N·m (83 lb-ft) in the 2001 manual
4th gen (N210) 2003–2009 6×139.7 (6×5.5) M12 x 1.5 106.1 mm 110 N·m (83 lb-ft) in the 2003, 2004 and 2009 manuals
5th gen (N280), early 2010–2014 6×139.7 (6×5.5) M12 x 1.5 106.1 mm 110 N·m; printed as 83 lb-ft in the 2010 manual and 81 lb-ft in the 2014 manual
5th gen (N280), late 2015–2024 6×139.7 (6×5.5) M12 x 1.5 106.1 mm 76 lb-ft (103 N·m) aluminum; 83 lb-ft (112 N·m) steel in the 2015, 2023 and 2024 manuals
6th gen, all, incl. TRD Pro and Trailhunter 2025–present 6×139.7 (6×5.5) M14 x 1.5 95.1 mm 97 lb-ft (131 N·m) aluminum; 154 lb-ft (209 N·m) steel in the 2025 manuals

The 2015 change is the one that catches 5th gen owners. Through 2014, Toyota printed one torque figure, 110 N·m, for every wheel. The 2015 4Runner owner’s manual splits it: 76 lb-ft (103 N·m) for the aluminum wheels on nearly every truck, and 83 lb-ft (112 N·m) for steel wheels, which on most trucks means the full-size steel spare. Every later 5th gen book we checked, through 2024, repeats the same pair. If you rotate the spare into service, it gets the steel number.

The 2010–2014 figure looks like it moved and did not. The 2010 4Runner owner’s manual lists 110 N·m and prints it as 83 lb-ft. The 2014 book lists the same 110 N·m and prints it as 81 lb-ft, which is the correct conversion. That is a rounding difference in the books, not a different spec. If you see 81 on a forum and 83 in your glovebox, that is why.

The 2025 change is bigger. The 2025 4Runner owner’s manual lists 97 lb-ft (131 N·m) for aluminum wheels and 154 lb-ft (209 N·m) for steel wheels, which on a 4Runner means the steel spare on some 20-inch trucks. Toyota tells owners to retighten the wheel nuts within 100 miles after a tire change, never to oil or grease the studs, and to check that the nuts are still tight after 1,000 miles on aluminum wheels. We go further on aftermarket wheels and re-check after the first 25 to 50 miles. New wheels seat in, and the nut that was right in the driveway is not always right on Friday.

All 6-lug 4Runners can start with our 6×5.5 wheels and filter by offset. Just filter for the right hub and thread first if the truck is a 2025 or newer.

What wheel and tire sizes came on each 4Runner?

Wheel and tire sizes for 1996 on come from Toyota’s owner’s manuals. Toyota does not print offsets in those books, so the offsets below come from fitment databases and OE wheel listings that agree with each other. Where they do not agree, we say so in the table. Diameters are calculated from the tire size and rounded.

Factory wheel and tire sizes by generation (Toyota manuals from 1996 on; offsets from cross-checked databases)
Generation or trim Factory wheel and offset Factory tire Approx. tire diameter
1st and 2nd gen (1984–1995) 15-inch steel or alloy; databases list 15 x 6 to 15 x 7 at about 0 to +8 mm (confirm) 225/75R15; 31×10.50R15 listed on some 4WD trucks (databases; confirm) 28.3 in.; 31 in.
3rd gen (1996–2002) 15 x 7 or 16 x 7 at about +15 mm P225/75R15; P265/70R16 28.3 in.; 30.6 in.
4th gen (2003–2009) 16 x 7 or 17 x 7.5 at about +30 mm; 18 x 7.5 at about +25 mm from 2006 P265/70R16; P265/65R17; P265/60R18 (2006–2009) 30.5 to 30.6 in.
5th gen SR5, TRD Off-Road and similar (2010–2024) 17 x 7 or 17 x 7.5 at about +12 to +15 mm P265/70R17 31.6 in.
5th gen Limited (2010–2024) 20 x 7 at about +15 mm (Toyota’s 2022 spec sheet says 20 x 7.5; the manuals say 20 x 7) P245/60R20 31.6 in.
5th gen TRD Pro (2015–2024) 17 x 7 TRD wheel at about +4 mm P265/70R17 (Nitto Terra Grappler all-terrain on later trucks) 31.6 in.
6th gen SR5 (2025–present) 17 x 7 at about +50 to +55 mm (databases differ) 245/70R17 30.5 in.
6th gen TRD Sport, Limited, Platinum 20 x 8 at about +45 to +55 mm (databases differ) 265/55R20 31.5 in.
6th gen TRD Off-Road 18 x 7.5 at about +55 mm; an optional 18 x 8 is listed at about +45 mm 265/70R18 (Toyota calls it a 33-inch all-terrain) 32.6 in.
6th gen TRD Pro and Trailhunter 18 x 8.5 (Toyota); about +20 mm per one database (confirm) 265/70R18 116H Toyo (Toyota calls it a 33) 32.6 in.

Two things stand out. First, factory 4Runner tires barely grew in twenty years: about 30.6 inches on the 3rd and 4th gen, 31.6 on the 5th gen, and 30.5 to 32.6 on the 6th gen. An owner who wants a true 33 or 35 is asking for a real change, not a small step. Second, look at the offsets. The 5th gen ran about +15 mm and the TRD Pro +4. Most 2025-and-newer grades run about +45 to +55 mm. That gap of 30 to 50 mm is why a wheel that looked right on a 2019 can sit more than an inch farther out on a 2025 at the same width.

A note on the TRD Pro and Trailhunter. Toyota’s 2025 4Runner press release says both grades get 33-inch Toyo tires on 18-inch wheels, bronze on the Trailhunter and black on the TRD Pro. The hybrid manual lists the tire as 265/70R18 116H on an 18 x 8.5 wheel, which works out to about 32.6 inches on paper, and lists a front and rear tread of 1,747 mm on those two grades against 1,667 mm on other trims. That is about 3 inches more track. When we size a step up from a TRD Pro, we start from the real tire diameter and the wider track, not the badge.

The 2025 manuals also list sizes we have not tied to a specific grade: a 245/70R18 on an 18 x 7.5 in the gas manual, and some 17-inch SR5 trucks with a temporary T175/90D18 spare instead of a full-size one. If your truck has the temporary spare, plan where a full-size spare will live before you upsize the tires.

How do offset and backspacing change what fits on a 4Runner?

Offset is the distance in millimeters from the wheel’s centerline to its mounting face. Positive offset tucks the wheel in toward the frame; negative pushes it out. Backspacing is the distance in inches from the mounting face to the inner lip, and on a 4Runner it decides whether a wide tire touches the upper control arm. The two are linked by width, so neither number means much alone. Our wheel offset and backspacing calculator does the conversion for any width and offset.

The table compares common sizes against two factory baselines: a 2010–2024 17 x 7 at +15 mm and a 2025-and-newer 18 x 7.5 at +55 mm. The figures are geometry, calculated from width and offset, so they apply to any brand.

Backspacing and outer lip position against 2010–2024 and 2025-and-newer factory wheels
Wheel Backspacing Outer lip vs. 2010–2024 17 x 7, +15 mm Outer lip vs. 2025+ 18 x 7.5, +55 mm
17 x 7, +15 mm (5th gen factory) 4.59 in. Baseline 1.33 in. farther out
17 x 7, +4 mm (5th gen TRD Pro) 4.16 in. 0.43 in. farther out 1.76 in. farther out
18 x 7.5, +55 mm (6th gen factory) 6.42 in. 1.33 in. farther in Baseline
18 x 8.5, +20 mm (6th gen TRD Pro, per one database) 5.54 in. 0.55 in. farther out 1.88 in. farther out
17 x 8.5, 0 mm 4.75 in. 1.34 in. farther out 2.67 in. farther out
17 x 9, -12 mm 4.53 in. 2.06 in. farther out 3.39 in. farther out

The right-hand column is the one 2025-and-newer owners should read twice. A 17 x 8.5 at 0 mm, a common choice on a 5th gen, sits about 2.7 inches farther out on a new 4Runner than the factory wheel does. That is a lot of poke on a body drawn around +55 mm wheels. It is also more leverage on the wheel bearings and steering parts. On a 2025-and-newer truck we start most builds closer to the factory offset and let the tire do the work.

For a leveled 2010–2024 4Runner on 33s, most builds land on a 17 x 8.5 near 0 mm or a 17 x 9 near -12 mm. Treat that as typical, not a spec. If you already know you want a 9-inch wheel, our 17×9 6×5.5 wheels page is where we would start.

What size tires fit a 4Runner on stock suspension, a leveling kit, and a lift?

The table shows the starting points our specialists use for 2010–2024 4Runners, the largest pool of 4Runners we see. These are typical community fitments, not Toyota specs and not a guarantee. A tire that clears with the truck parked can still touch at full lock, under compression, or with a loaded roof rack and a full cargo area.

Typical 2010–2024 4Runner tire, suspension, and wheel combinations (typical community fitment, not guaranteed)
Tire Stock height Leveling kit (about 2 to 3 in. front) 3 in. or more of lift Typical wheel and offset
About 31.6 in. (265/70R17, factory) Fits Fits Fits; more lift than this tire needs 17 x 7 to 17 x 8, about 0 to +15 mm
About 32 in. (275/70R17 class) Usually fits; light rub at full lock is possible Fits Fits 17 x 7.5 to 8.5, about 0 to +15 mm
33 in. (285/70R17, 255/85R17 class) Often rubs at full lock The usual home for 33s, typically with mud flaps removed and often trimming or a body mount modification Fits 17 x 8.5 to 9, about 0 to -12 mm
35 in. (35×12.50R17, 315/70R17 class) No No With aftermarket upper control arms, trimming, and usually a body mount modification 17 x 8.5 to 9, about 0 to -12 mm

Our 4Runner lander lists the same pattern of common fitments: 17 x 8 with 265/70R17 and 17 x 8.5 with 275/70R17 on stock and mild setups; 17 x 9 with 285/70R17 on leveled and trail builds; and 17 x 9 or 17 x 10 with 35×12.50R17 on properly lifted trucks. For a factory-size replacement, our 265/70R17 tires page has the sizes the 5th gen came on.

If a 33 is the goal on a 5th gen, compare tread patterns and load ranges on our 285/70R17 tires page before you settle on a wheel.

Where do 33s rub on a 4Runner?

In our experience the contact points show up in roughly this order on 2010–2024 trucks:

  • Front mud flaps and the lower bumper corners. The first thing a taller tire touches at full lock. Most owners remove the flaps before anything else.
  • The body mount behind the front wheel. The well-known 4Runner contact point with 33s at full lock. Fixing it means trimming or modifying the mount, which is a body-shop job, not a driveway job.
  • Front of the fender liner. Contact at full lock and under compression. Heat-forming or trimming usually handles it.
  • Upper control arm. A wide tire on a wheel with too much backspacing touches the upper arm, especially after a leveling kit steepens the arm angle. Less backspacing is the cleaner fix; a spacer is not our first choice.

What fits older 4Runners?

On 2003–2009 trucks the factory tire is about 30.6 inches. In our experience a 31.6-inch tire such as 265/70R17 fits a stock 4th gen, and 33s typically want a leveling kit or lift plus trimming. The 1984–2002 trucks came on 15- and 16-inch wheels and much smaller tires, so we set those builds up one at a time, starting with how the suspension has already been modified. Again, typical, not guaranteed.

What changes on 2025-and-newer 4Runners?

The 2025 4Runner rides on the same TNGA-F platform as the current Tacoma, and it has only a couple of model years of aftermarket data behind it. Three things change our approach. The factory offsets are much higher, so the offset you pick moves the tire farther than it did on a 5th gen. The smallest factory wheel is 17 inches, so we do not assume a 16 clears the brakes; we check every wheel. And the driver-assist system cares about tire size and ride height. TRD Off-Road, TRD Pro, and Trailhunter trucks already leave the factory on about 32.6-inch tires, so the room left for a bigger tire is smaller than the badge suggests. Our 33-inch tires page covers the step up.

The driver-assist point is written into the 2025 4Runner manual, in the Toyota Safety Sense 3.0 section, for lifts up to 4 inches including tire height. Toyota says the system operates normally on factory suspension with factory tire sizes. With Toyota’s genuine 2.5-inch lift kit and tires up to 3 inches larger than factory, the system “may not operate properly” and Toyota tells owners to have a dealer verify and change the settings. Other tire sizes fall outside what the system is designed for, and a non-genuine lift requires a Toyota facility to disable the Toyota Safety Sense 3.0 functions. Read that section before you plan a lift and 35s on a new truck.

Will Tacoma, Tundra, or other 6×139.7 wheels fit a 4Runner?

Same bolt pattern does not mean same wheel. According to fitment databases, the 2010–2024 4Runner uses the same 106.1 mm hub and M12 x 1.5 studs as 2005–2023 Tacomas, and the 2025-and-newer 4Runner uses the same 95.1 mm hub and M14 x 1.5 studs as the 2024-and-newer Tacoma. Factory offsets and load ratings still differ, so check both. Our Tacoma wheel and tire fitment guide covers the Tacoma side in the same detail.

Tundra wheels need more care. The 2007–2021 Tundra is not a 6×139.7 truck at all, according to the databases we use; the 2022-and-newer Tundra is 6×139.7 and is listed with the same 95.1 mm hub and M14 x 1.5 studs as the 2025 4Runner, but Tundra wheels are built around a heavier full-size truck’s offset and load. Our Toyota Tundra wheels page lists what fits those trucks.

GM and Ram factory wheels go the other way. The Silverado 1500 and Sierra 1500 use a 78.1 mm bore and the Ram 1500 uses 77.8 mm, both far smaller than any 4Runner hub, so a factory wheel from either truck will not sit on a 4Runner. Most aftermarket 6×139.7 wheels are bored large enough for Toyota hubs and center with a ring.

What lug nuts and hub-centric rings does a 4Runner need with aftermarket wheels?

Three things have to match: thread, seat, and length. Thread is M12 x 1.5 through 2024 and M14 x 1.5 from 2025, according to the fitment databases we checked. Seat is set by the wheel, not the truck. Toyota alloy wheels clamp against a flat washer on the nut; the 2025 manual describes tightening until “the washer of the nut” contacts the wheel, and the tapered end of the nut is for the steel wheels. Most aftermarket wheels use a 60-degree conical seat. Factory Toyota alloy nuts on a conical-seat wheel will not clamp the way the wheel was designed to.

Hub-centric rings bridge the gap between a wheel’s larger center bore and the hub: 106.1 mm on 1984–2024 trucks, 95.1 mm on 2025-and-newer. A wheel bored to 95.1 mm for the new truck will not fit an older 106.1 mm hub at all, so factory 2025 take-offs are not an option for a 5th gen.

Can I move my 5th gen wheels to a 2025-and-newer 4Runner?

They bolt on, but plan for parts. The 106.1 mm bore clears the new 95.1 mm hub, so you need a 106.1 to 95.1 mm ring. The old M12 nuts will not thread onto M14 studs, and wheels drilled for M12 studs can have lug holes too narrow for some M14 nuts, so the nut has to match both the stud and the hole. Never drill out a wheel’s lug holes yourself. Then check the offset: a factory 17 x 7 at +15 mm sits about 1.3 inches farther out than the new truck’s 18 x 7.5 at +55 mm. And confirm the wheel clears the newer truck’s brakes before you mount tires.

Will TPMS work with new wheels on a 4Runner?

Federal rules require a TPMS on vehicles like these. FMVSS 138 was phased in from the 2006 model year and required all covered light vehicles by September 1, 2007, which generally means the 2008 model year. The rule, published in the Code of Federal Regulations at 49 CFR 571.138, requires a low-pressure warning when a tire falls 25 percent below the recommended cold pressure, and owner’s manual language warning that replacement tires or wheels can stop the system from working.

The process changed with the generations. The 2023 4Runner owner’s manual puts it under Vehicle Settings, where “Change Wheel Set” registers the ID codes of the tire pressure sensors. The 2025 manual adds that the system can store two sets of ID codes, for example a winter set, and says owners can register the codes themselves. That makes a second set for winter or the trail easier to live with on either truck. A shop with the right TPMS tool can usually do it too.

In practice, healthy factory sensors often move to aftermarket wheels that accept a valve-stem sensor. Our explainer on whether your old TPMS sensors can move to new wheels covers when to reuse sensors and when to replace them. One more check: a larger LT tire may want a different cold pressure than the placard. If it does, set the system at the new pressure; Toyota’s manuals include an initialization step for exactly that.

Does a bigger tire change gearing and the speedometer?

Yes, on both counts. A taller tire covers more ground per revolution, so the speedometer reads low and the effective axle ratio drops. The math: effective ratio equals the axle ratio times the old tire diameter, divided by the new tire diameter. Take a 3.73 axle ratio as an example. On a factory 265/70R17 (about 31.6 inches), stepping to a 33 lands near 3.57, and a 35 drops it to about 3.37. On a 4Runner that tows or climbs loaded, that is the difference between a truck that holds its gear and one that hunts. Have the tire size recalibrated after a size change so the speedometer and odometer stay accurate.

What load rating do 4Runner wheels and tires need?

Each wheel carries a maximum load rating from its maker, and each tire carries a load index. The placard on the driver’s door jamb gives the factory tire size and pressure, and Toyota’s manuals list the load index of each factory tire, from 110 on the 2025 SR5’s 245/70R17 to 116 on the 265/70R18. Replacement tires should not have a lower load index than the originals, and the wheel should be rated for the truck’s weight with margin for a rooftop tent, a drawer system, or a trailer. Overland 4Runners get heavy fast. Our Search By Vehicle tool filters 4Runner wheels by load rating along with bolt pattern, offset, and center bore, and every order is reviewed by a fitment specialist.

LT tires add stiffer construction and higher load ranges than P-metric and standard-load tires. They ride firmer and weigh more, and on a midsize SUV the weight shows up in braking and fuel use. On a daily driver that rarely carries much, a standard-load or XL tire at the right load index is often the better match. On a heavy overland build, we would rather go LT.

How do we build a 4Runner wheel and tire package?

We recommend a complete set on most 4Runner builds, because tire size, wheel width, and offset have to be chosen together. We mount and balance every package on Hunter equipment, and TPMS, lug hardware, hub-centric rings, and Road Force balancing are options at checkout. Our guide to how we mount and balance packages explains what happens before a set ships.

Before an order ships, a specialist runs a 5-point check of bolt pattern, offset, center bore, width, and brake clearance. On a 4Runner, the center bore line is the one that catches 2025-and-newer trucks, and the offset line catches 5th gen setups copied onto a 6th gen. Our 100% Fitment Guarantee page explains what is covered. Changing the tire size away from what our Search By Vehicle tool recommends can void it, so tell us about your leveling kit or lift before you order, not after.

Wheels ship out in 2 to 4 business days and mounted packages in 4 to 8, by FedEx Ground, to the lower 48 states. Eligible unused products can be returned within 60 days, subject to the conditions on our returns page. If you would rather spread the cost of a full set, our guide to financing wheels and tires covers the options.

What should you check before you order 4Runner wheels and tires?

Run this list in order. It is the same order our specialists use on the phone.

  1. Identify the generation and trim. Note the model year: 1984–1989, 1990–1995, 1996–2002, 2003–2009, 2010–2024, or 2025 and newer. Note TRD Pro, Trailhunter, TRD Off-Road, or Limited, and any lift or leveling kit.
  2. Read the door placard. Write down the factory tire size, load index, and cold inflation pressure. Replacement tires should not have a lower load index than the originals, and the wheel’s load rating should suit the 4Runner and what you carry on the roof and in the back.
  3. Choose the tire size first. Decide on the tire for how you use the 4Runner, then the suspension it typically needs: stock for about 32 inches on a 2010–2024 truck, a leveling kit for 33s, and a 3-inch or larger lift with supporting parts for 35s.
  4. Pick wheel diameter, width, and offset for that tire. Start from your generation’s factory offset (about +15 mm on 1996–2002 and 2010–2024 trucks, about +25 to +30 mm on 2003–2009, about +45 to +55 mm on most 2025-and-newer grades), run the numbers in an offset and backspacing calculator, and check brake clearance.
  5. Confirm bolt pattern, center bore, and lug hardware. Match 6×139.7, use a hub-centric ring if the wheel bore is larger than 106.1 mm (95.1 mm on 2025 and newer), and buy lug nuts in the right thread (M12 x 1.5 through 2024, M14 x 1.5 from 2025) with the seat the wheel calls for.
  6. Plan TPMS. Order sensors or confirm your old ones are healthy and compatible, register the new sensor IDs to the truck after installation, and check that the TPMS light is off.
  7. Plan driver-assist and speedometer checks. On 2025-and-newer trucks, read the Toyota Safety Sense 3.0 section of the owner’s manual before changing tire size or lift height. On any year, have the tire size recalibrated if the speedometer reads off.
  8. Install, torque, and re-check. Torque the lug nuts to your year’s spec in a star pattern with a torque wrench (76 lb-ft alloy or 83 lb-ft steel on 2015–2024; 97 lb-ft alloy or 154 lb-ft steel from 2025), re-check after the first 25 to 50 miles, and get an alignment if lift, tire size, or offset changed.

Frequently asked questions

What is the bolt pattern on a Toyota 4Runner?

6×139.7, also written 6×5.5, on every U.S. 4Runner generation in the fitment databases we checked, from 1984 through the current 2025-and-newer truck. The pattern never changed. What changed in 2025 is the hub diameter and stud thread, so a matching bolt pattern alone does not make a wheel fit.

What size lug nuts does a 4Runner use?

Fitment databases list M12 x 1.5 studs on 1984–2024 4Runners and M14 x 1.5 on 2025-and-newer trucks. Toyota alloy wheels use a flat-seat nut with a washer, while most aftermarket wheels need a 60-degree conical-seat nut, so plan on new lug nuts with most aftermarket wheels.

What is the lug nut torque on a Toyota 4Runner?

Toyota lists 110 N·m (83 lb-ft) in the 2001, 2009 and 2010 manuals; the 2014 manual prints the same 110 N·m as 81 lb-ft. 2015–2024 manuals list 76 lb-ft (103 N·m) for aluminum wheels and 83 lb-ft (112 N·m) for steel. 2025-and-newer manuals list 97 lb-ft (131 N·m) aluminum and 154 lb-ft (209 N·m) steel.

What is the center bore on a 4Runner?

Fitment databases list 106.1 mm for 1984–2024 4Runners and 95.1 mm for 2025-and-newer trucks. Toyota’s owner’s manuals do not print the hub size. Use a hub-centric ring whenever the wheel’s bore is larger than the hub.

Will 5th gen 4Runner wheels fit a 2025 4Runner?

They bolt on, because the bolt pattern is the same and the 106.1 mm bore clears the 95.1 mm hub, but they are not a direct fit. You need M14 x 1.5 nuts that fit the wheel’s seat and lug holes, a 106.1 to 95.1 mm hub-centric ring, and an offset check, since a 5th gen wheel at about +15 mm sits more than an inch farther out than the new truck’s +55 mm factory wheels.

What size tires fit a stock 4Runner?

On a stock 2010–2024 4Runner, tires around 32 inches, such as 275/70R17, typically fit, with light rubbing at full lock possible. The factory 265/70R17 is about 31.6 inches. 2025-and-newer TRD Off-Road, TRD Pro and Trailhunter trucks come on 265/70R18, about 32.6 inches. Treat these as typical, not guaranteed.

What size tires fit a leveled 4Runner?

With a typical front leveling kit, many 2010–2024 4Runners run 33-inch tires such as 285/70R17 on a 17-inch wheel at about 0 to -12 mm, usually after removing the front mud flaps and often with trimming or a body mount modification. Treat this as typical, not guaranteed.

What wheels and tires come on the 4Runner TRD Pro and Trailhunter?

On 2025-and-newer trucks, Toyota fits both grades with 33-inch Toyo tires on 18-inch wheels, bronze on the Trailhunter and black on the TRD Pro. The hybrid owner’s manual lists 265/70R18 116H on an 18 x 8.5 wheel. The 2015–2024 TRD Pro used P265/70R17 on a 17 x 7 TRD wheel.

Who can check your 4Runner build before you order?

Send us the year, trim, suspension, and the tire size you want, and a specialist will tell you what fits and what it will take. You can contact a fitment specialist online at any hour, or call or text 1-866-757-4679 Monday through Friday, 8:30 AM to 6:00 PM Eastern. If the honest answer is that your 2025 needs different lug nuts and a different offset than your old 5th gen setup, we will tell you before you spend the money.

Want to hear from other 4Runner owners first? Our customer reviews page shows our 4.8-star Shopper Approved rating across 2,045 reviews.